Make sure to read the Getting Started section if you haven’t done so yet.
Writing To Display¶
Line feed characters (
\n) move down one line and carriage returns (
move to the beginning of the current line.
lcd.write_string('Raspberry Pi HD44780') lcd.cursor_pos = (2, 0) lcd.write_string('https://github.com/\n\rdbrgn/RPLCD')
You can also use the convenience functions
write line feed (
\n) or carriage return (
\r) characters to the display.
lcd.write_string('Hello') lcd.crlf() lcd.write_string('world!')
After your script has finished, you may want to close the connection and
optionally clear the screen with the
When using a GPIO based LCD, this will reset the GPIO configuration. Note that doing this without clearing can lead to undesired effects on the LCD, because the GPIO pins are floating (not configured as input or output anymore).
Clearing the Display¶
You can clear the display by using the
clear() method. It
will overwrite the data with blank characters and reset the cursor position.
Alternatively, if you want to hide all characters but keep the data in the LCD
memory, set the
display_enabled property to
RPLCD supports the two most commonly used character maps for HD44780 style displays: A00 and A02. You can find them on pages 17 and 18 of the datasheet.
The default character map is
A02. If you find that some of the characters
you are writing to the display turn out wrong, then try using the
lcd = CharLCD(..., charmap='A00')
As a rule of thumb, if your display can show Japanese characters, it uses
A02. To show the entire character map on your LCD, you
can use the
show_charmap target of the
Should you run into the situation that your character map does not seem to match
A00 or the
A02 tables, please open an issue on Github.
The same thing counts if you have a character that should be supported by your character map, but which doesn’t get written correctly to the display. Let me know by opening an issue!
In case you need a character that is not included in the default device character map, there is a possibility to create custom characters and write them into the HD44780 CGRAM. For more information, see the Creating Custom Characters section.
Creating Custom Characters¶
The HD44780 supports up to 8 user created characters. A character is defined by a 8x5 bitmap. The bitmap should be a tuple of 8 numbers, each representing a 5 pixel row. Each character is written to a specific location in CGRAM (numbers 0-7).
>>> lcd = CharLCD(...) >>> smiley = ( ... 0b00000, ... 0b01010, ... 0b01010, ... 0b00000, ... 0b10001, ... 0b10001, ... 0b01110, ... 0b00000, ... ) >>> lcd.create_char(0, smiley)
To actually show a stored character on the display, you can use hex escape codes with the location number you specified previously. For example, to write the character at location 3:
The escape code can also be embedded in a longer string:
>>> lcd.write_string('Hello there \x03')
The following tool can help you to create your custom characters: https://omerk.github.io/lcdchargen/
Changing the Cursor Appearance¶
The cursor appearance can be changed by setting the
cursor_mode property to one of the following three
hide– No cursor will be displayed
line– The cursor will be indicated with an underline
blink– The cursor will be indicated with a blinking square
If you’re using an LCD connected through the I²C bus, you can directly turn on
the backlight using the boolean
By setting the
pin_backlight parameter in the
constructor, you can control a backlight circuit.
First of all, you need to build an external circuit to control the backlight,
most LCD modules don’t support it directly. You could do this for example by
using a transistor and a pull-up resistor. Then connect the transistor to a GPIO
pin and configure that pin using the
pin_backlight parameter in the
constructor. If you use an active high circuit instead of active low, you can
change that behavior by setting the
backlight_mode to either
active_low. Now you can toggle the
backlight_enabled property to turn the backlight on
Automatic Line Breaks¶
By default, RPLCD tries to automatically insert line breaks where appropriate to achieve (hopefully) intuitive line wrapping.
Part of these rules is that manual linebreaks (either
immediately follow an automatically issued line break are ignored.
If you want more control over line breaks, you can disable the automatic system
by setting the
auto_linebreaks parameter of the
CharLCD constructor to
lcd = CharLCD(..., auto_linebreaks=False)
I wrote a blogpost on how to implement scrolling text: https://blog.dbrgn.ch/2014/4/20/scrolling-text-with-rplcd/
To see the result, go to https://www.youtube.com/watch?v=49RkQeiVTGU.